from web site
It's easy to construct, however due to the fact that you'll be working with electrical energy, I suggest employing an electrician to build it for you or at the very least provide some assistance. If you connect something improperly, you might potentially electrocute yourself, so please be cautious and take all required measures.
You might do this task for $50-$ 100, depending upon the products you choose. This task will cost me $70.
This project is rather basic, nevertheless it will take some time to wrap all of those components with tape. That's essentially the only drawback I can see, thinking about the materials are inexpensive, you do not require any hardware, and it seems like it can endure some abuse from rough handling during a shot.
It's imaginable that the tape isn't the ideal thing to place over the LEDs since it will alter how the light acts ... perhaps ... however it does not damage to experiment. If it ends up being a flop, all you've really lost are a couple of dollars' worth of LED rope lights and a few of hours of your time.
What You'll Need
A wire
Rope lights LED
Cardboard
Aluminum foil
Transparent tape
TOOLS
Jigsaw
Drill
Wire cutters and strippers
Screwdriver
Pliers
Box cutter
Determining tape
Pencil
String
DIRECTIONS Step and mark the 12 inch from middle of your plywood. Then, using the thread as a guide, sketch the inner circle that needs to be cut off. Use among the light sockets to determine how far you need to go. Then repeat for the outdoors circle.
Cut out your inner and outer rings with the jigsaw. Leave one corner of the external circle uncut to accommodate the switch and installing bracket. When you're completed, you must have a teardrop shape with a hole in it. For the light sockets, you can measure and mark 12 similarly spaced places. I simply kept in mind whatever and spaced my sockets out without measuring. Drill the 12 holes with a 7/16 ′ ′ bit or anything near adequate to enable 4 wires to go through.
The wire should then be stripped. Cut 8-10 ′′ pieces of the black and white pairs off the outer guard. You'll require an overall of 12 pairings. Then, using the pliers, form hooks on the bare wire and strip the ends of each wire (about 3/4 ′′ raw wire). You'll wire each light socket by threading four wires through each of the 12 holes you made.
Make certain that the polarity is not reversed. The 2 white wires connect to the light socket's two gold contacts. The two black wires are linked to the silver contacts. Make sure you feed the wire onto the contacts clockwise so that it does not spin off when the screws are tightened up. Inspect your work two times and make certain you do not make any mistakes. As you wrap the wire around the ring, you must have 1 white and 1 black wire left over. Do not link them to the socket you began with; instead, connect them to the switch according to the instructions that came with your switch.
Dimmer switch: The white wire links straight to the power supply.
The black cable is linked to the switch.
The switch's ground connects to the ground of the green power cable television.
Wire adapters and tape need to be used to secure your wires.
Now is a fantastic minute to put your skills to the test. Place a light bulb into the last light socket and test it. It should operate similarly to a standard . If it does not work, you slipped up and must disconnect your light and verify your electrical wiring.
Zip tie whatever in place once you have actually validated that your electrical wiring works which it's not hooked into an outlet. Drill tiny holes to accommodate the zip ties. You may also remove the teardrop's suggestion to develop a flat edge for your installing bracket. Crucial: When you're working on your lamp, make certain you're not plugged into the wall! Everything, including the bracket and switch, is zip tied. Check for bare wires coming out the back of the light sockets or the switch.
Put your ring light on a light stand, insert your bulbs, and test it out!
Find ideal case for your iphone, these cases will perfectly fit your phone and doesn't let it slide from the ring light. Just On Online Store. https://gornetcases.com/collections/iphone-12-pro-max-wallet-cases